Surface Preparation and concrete polishing is a competitive industry and the ability to achieve quality outcomes is essential for getting your projects noticed. This blog will touch on the 9 most common grinding and polishing mistakes and why it’s important to correct them.
MISTAKE 1; Not properly managing customer expectations
This may not seem like something that is overly important but in reality it’s incredibly important. Every customer has a vision of how they want the floor to look upon completion- sometimes it’s achievable but not always, so it is important to effectively manage customer expectations. This is often what contractors new to polishing and grinding find most difficult.
It is so important to properly educate your customer on what is a reasonable expectation for their floor, because every floor is different and has its own “personality” so to speak.
Here are some potential topics that should be covered before work begins…
Once you understand how metal bond diamond tooling works, you can use the general rule of thumb when selecting the tooling for your job.
The “rule of thumb” is: soft concrete requires hard bond diamonds and hard concrete needs soft bond diamonds;
Metal Bond Tooling Guide:
For Matching the Correct Diamond Bond Hardness to Concrete Hardness.
Very Hard Concrete (6,000-8,000 PSI) ----------- Extra Soft Bond Diamonds
Hard Concrete (5,000-6,000 PSI) ------------ Soft & Extra Soft Bond Diamonds
Medium Concrete (3,500 – 5,000 PSI ) ------------ Medium Bond Diamonds
Soft Concrete (3,500 PSI and under) ------------ Hard Bond Diamonds
A major mistake contractors make, is selecting the incorrect bond for the concrete hardness and doing so will result in two outcomes…
Either way, you end up wasting your time, and money, and your results will suffer.
CLICK HERE TO BETTER UNDERSTAND HOW DIAMOND TOOLING WORKS
Mistake 3: Running the grinder unnecessarily Fast
A common mistake an operator can make when feeling under pressure, is running the grinder at an unnecessarily fast speed.
We tend to see this happening when an operator wants a faster production rate and will turn up the speed of the grinder in an effort to accomplish more in less time. However, this increased speed can overheat and “glaze over” your diamonds (especially on hard concrete) which prevents them from cutting properly, or at all (as mentioned earlier).
To give you an example, our Predator grinder/polishers run a maxim drum speed of 1,200 rpm when the dial set at 10 (full power). Although it can go 1,200 rpm if need be, generally it’s recommended to set the dial around 4.5-5.5 which runs the drum at approximately 600rpm. An operator can then adjust up a little or down a little to get the best performance.
Finding the right speed is important but speed alone doesn't necessarily equate to better production rates.
MISTAKE 4, NOT UNDERSTANDING DOWNWARD PRESSURE
Ultimately, greater downward pressure = faster grinding
There are two ways of achieving this: A heavier machine will obviously give more head pressure but, so do different diamond options;
Single bar Double bar Single round Double round
If you are operating a smaller machine (like the alpha 9", DFG280 11", p550y & P-2400 for example) a Single Rectangle or single round will give more down pressure because you have double the square inch pressure, compared to a double round or rectangle; allowing it to cut faster. The opposite is true of the larger machines where a double segment will offer better performance because it is grinding a larger space at one time.
Although sometimes price isn’t always an indicator of quality (or lack thereof) when it comes to diamond tooling, it’s important to make sure that price isn't your only criteria of consideration for purchase.
Poor quality diamonds wear faster, and inconsistently. They can scratch floors, and generally perform poorly, usually with limited or no support from the vendor.
Buy from a trusted vendor willing to stand behind their products. This will save you time and money in the long run.
A metal bond diamond will grind and polish almost anything from steel, brass, glass, etc. AS LONG AS, the material is not “above grade” (raised above the floor surface).
Make sure you inspect the floors for anything above grade and either cut off, hand grind to level, or smack with a hammer to knock below grade. Once you’ve eliminated the above grade issues, you can grind it along with the concrete resulting in an interesting detail that adds to the personality of the floor. If you DO NOT inspect the floor and deal with the parts above grade before you begin grinding, you will most likely knock your diamond segment off and can do a lot of damage to your machine.
Here are a couple of questions and cautions for determining what your starting diamond will be…
Here are some important things to be aware of…
When polishing a floor, you must keep an eye on the finish you’re producing as you go. If you see faint scratches starting to appear you must remove them immediately, rather than “hope” the problem will cure itself… because it won’t - it will only continue to manifest as you polish up the floor.
For instance, if you are running a 100G resin bond diamond and you start to see scratches, do not think your next step, with 200G resins, will remove them. You must remove them with the 100G or if necessary fall back to a more aggressive diamond like a 50G or 30G resin before you move onto the next step.
To reiterate: Remove the problem scratches as soon as you see them. Do NOT leave them and hope they go away… because they won’t and your results will suffer because of it.
There are regulations regarding cutting concrete because of the health concerns related to silica dust in the concrete grindings that can be released into the air during the grinding process and must be captured a couple of different ways, the first being a dust collection system (a vacuum to the layman LOL) but, and this is critical, not just any vacuum but a HEPA FILTER system, these take 99.97 percent of the friable material out of the air making it safe to work and protects you from a really big fine in most of the world!
the second is WATER, you can grind wet and this keeps the silica-containing dust captured in the concrete slurry. it is important to note that that slurry must be disposed of correctly as it is considered hazardous waste in most countries.
CLICK HERE FOR INFORMATION ON HOW TO DISPOSE OF CONCRETE SLURRY
Concrete grinding and polishing can really be a profitable and satisfying profession when you stand back and look at a well-polished floor but can be a frustrating profession when things do not go well, hopefully the information covered in the article helps you keep projects interesting and profitable.